CONVENIENCE PRODUCTS -- TOUCH'N FOAM  -- 8030-00F054517
<pre>=====================  Product Identification  =====================

Product ID:TOUCH'N FOAM
MSDS Date:03/01/1996
FSC:8030
NIIN:00F054517
=== Responsible Party ===
Company Name:CONVENIENCE PRODUCTS
Address:866 HORAN DR
City:FENTON
State:MO
ZIP:63028-2416
Country:US
Info Phone Num:314-349-5333
Emergency Phone Num:314-349-5333
CAGE:CONVE
=== Contractor Identification ===
Company Name:CONVENIENCE PRODUCTS
Address:866 HORAN DR
City:FENTON
State:MO
ZIP:63028-2416
Country:US
Phone:314-349-5333
CAGE:CONVE

=============  Composition/Information on Ingredients  =============

Ingred Name:POLYURETHANE RESIN
Fraction by Wt: 50-58%

Ingred Name:DIPHENYLMETHANEDIISOCYANATE (MDI), METHYLENE BIS
    (PHENYLISOCYANATE), 4,4 DIPHENYLMETHANE DIISOCYANATE (MDI)
CAS:101-68-8
RTECS #:NQ9350000
Fraction by Wt: 5-15%
Other REC Limits:0.005 PPM
OSHA PEL:0.02 PPM
ACGIH TLV:0.051 MG/CUM
EPA Rpt Qty:1 LB
DOT Rpt Qty:1 LB

Ingred Name:CHLORODIFLUOROMETHANE, FREON 22, MONOCHLORODIFLUOROMETHANE 
    (SUSPECTED ANIMAL CARCINOGEN BY-IARC GROUP 3)  *97-3*
CAS:75-45-6
RTECS #:PA6390000
Fraction by Wt: 15-25%
Other REC Limits:1000 PPM
OSHA PEL:1000 PPM
ACGIH TLV:3540 MG/CUM
Ozone Depleting Chemical:2

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:ORAL LD50(RAT): >10,000 MG/KG
Routes of Entry: Inhalation:YES  Skin:NO  Ingestion:NO
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:POLYURETHANE RESIN-EYES: MAY CAUSE
    DAMAGE. ISOCYANATES MAY CAUSE SENSITIZATION. CROSS SENSITIZATION
    MAY OCCUR. OVEREXPOSURE TO ISOCYANATES CAUSES LUNG DAMAGE & REDUCED
    LUNG FUNCTION WHICH MAY BE PERMA NENT.
Explanation of Carcinogenicity:NONE
Effects of Overexposure:WHEEZING, SHORTNESS OF BREATH, DIFFICULTY
    BREATHING, ASTHMA.
Medical Cond Aggravated by Exposure:BREATHING DIFFICULTIES, CHEST
    DISCOMFORT,

=======================  First Aid Measures  =======================

First Aid:INHALATION: REMOVE TO FRESH AIR. GIVE OXYGEN/CPR IF NEEDED.
    KEEP QUIET. DON'T GIVE STIMULANTS. SKIN: IF FROSTBITTEN, WARM
    SLOWLY W/WATER/WASH W/SOAP & WATER. REMOVE WET FOAM W/ACETONE/NAIL
    POLISH REMO VER. IF FOAM DRIES, APPLY PETROLEUM JELLY/LANOLIN,
    LEAVE ON FOR 1 HOUR & WASH THOROUGHLY. DON'T REMOVE W/SOLVENTS.
    EYES: FLUSH W/WATER FOR 15 MINS. OBTAIN MEDICAL ATTENTION IN ALL
    CASES.

=====================  Fire Fighting Measures  =====================

Flash Point:>400F
Extinguishing Media:WATER FOG, FOAM, CO2/DRY CHEMICAL.
Fire Fighting Procedures:WEAR SCBA & TURNOUT GEAR.
Unusual Fire/Explosion Hazard:TEMPS >120F WILL INCREASE THE PRESSURE IN
    THE CAN, WHICH MAY LEAD TO RUPTURING CURED FOAM. PRODUCT WILL BURN
    & ISN'T INTENDED FOR USE IN APPLICATIONS >250F.

==================  Accidental Release Measures  ==================

Spill Release Procedures:ALLOW FOAM TO CURE(HARDEN).

======================	Handling and Storage  ======================

Handling and Storage Precautions:STORE IN A COOL, DRY PLACE. STORAGE
    TEMP IS 60F-80F. STORAGE >90F SHORTENS THE SHELF LIFE. DON'T STORE
    >120F. PROTECT CONTAINERS FROM PHYSICAL ABUSE.
Other Precautions:DON'T STORE IN AUTO/IN DIRECT SUNLIGHT. STORE
    UPRIGHT.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:NONE REQUIRED IF IN WELL VENTILATED AREA.
Ventilation:LOCAL EXHAUST TO MAINTAIN PEL AREA.
Protective Gloves:REQUIRED
Eye Protection:FACE SHIELD, GOGGLES/SAFETY GLASSES
Other Protective Equipment:COVERALLS, LONG SLEEVE SHIRTS & HEAD
    COVERING.
Work Hygienic Practices:REMOVE/LAUNDER CONTAMINATED CLOTHING BEFORE
    REUSE. CONTAMINATED EQUIPMENT/CLOTHING SHOULD BE CLEANED AFTER EACH
    USE.
Supplemental Safety and Health

==================  Physical/Chemical Properties  ==================

Boiling Pt:B.P. Text:-41.4F
Vapor Pres:136
Vapor Density:2.98
Spec Gravity:1.1
Solubility in Water:INSOLUBLE
Appearance and Odor:GEL UNDER PRESSURE W/FAINT ETHER-LIKE ODOR

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
WATER, ALCOHOLS, STRONG BASES, FINELY POWDERED METAL, ALUMINUM,
    MAGNESIUM/ZINC, STRONG OXIDIZERS.
Stability Condition to Avoid:HEAT, FLAMES, HOT METAL SURFACES, DIRECT
    SUNLIGHT.
Hazardous Decomposition Products:CO, CO2, NITRIC OXIDES, HYDROGEN
    CHLORIDE.

====================  Disposal Considerations  ====================

Waste Disposal Methods:DISPOSE OF IAW/FEDERAL, STATE & LOCAL
    REGULATIONS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.